卷簾門，是以多關節活動的門片一片片并聯拼接而成的，現在許多的大型或者門面都安裝此種門，因?yàn)椴粌H收縮方便，而且節省空間，當然系數也高?？删砗熼T如何安裝呢?下面就3種不同類型的濟南卷簾門安裝步驟介紹給大家。

Rolling shutter doors are made by connecting multi joint movable door pieces in parallel. Nowadays, many large shopping malls or storefronts install this type of door because it is not only convenient to shrink, but also saves space, and of course, has a high safety factor. How to install a roller shutter door? Below are the installation steps for three different types of Jinan roller shutter doors.

1、電動卷簾門安裝方法：

1. Installation method of electric roller shutter door:

先，在需要安裝的門框框口位置畫線，表明尺寸的大小。注意：框內高度比門扇的高度要高一點點。

Firstly, draw a line at the position of the door frame opening that needs to be installed to indicate the size. Note: The height inside the frame is slightly higher than the height of the door leaf.

把電動卷簾門的門框固定，但是洞口兩側地面要記得預留凹槽。

Fix the door frame of the electric roller shutter door, but remember to reserve grooves on the ground on both sides of the opening.

然后，安裝電動卷簾門扇主體門扇。安裝時，一定要保證電動卷簾門與墻體結成整體，而且封閉性要做好，再將洞口及墻體粉刷，確保美觀度。粉刷完后，應對門試試開啟關閉是否順暢自如。

Then, install the main body of the electric roller shutter door leaf. When installing, it is necessary to ensure that the electric roller shutter door is integrated with the wall, and the sealing must be done well. Then, the opening and wall should be painted to ensure aesthetics. After painting, try opening and closing the door smoothly and smoothly.

2、防火卷簾門安裝方法：

2. Installation method of fireproof rolling shutter door:

a、按門的型號，量測產品各部位基本尺寸，檢查門的洞口是否與卷簾門尺寸相符，導軌和支架的預埋位置、數量是否正確。然后，測量洞口標高，彈出兩導軌垂線及卷筒線。

a. Measure the basic dimensions of each part of the product according to the door model, check whether the door opening matches the size of the rolling shutter door, and whether the embedded positions and quantities of the guide rail and bracket are correct. Then, measure the elevation of the opening and snap out the vertical lines of the two guide rails and the centerline of the drum.

b、將墊板電焊在預埋鐵板上，用螺絲固定卷筒支架，安裝卷筒。卷筒的安裝應轉動靈活。

b. Weld the base plate onto the embedded iron plate, fix the drum bracket with screws, and install the drum. The installation of the drum should rotate flexibly.

c、安裝減速器、傳動系統、裳電氣拴街系統。

c. Install reducers, transmission systems, and electrical street systems.

d、將事先裝配好的簾板安裝在卷筒上。緊接著安裝導軌，按照圖紙規定的位置，將兩側及上方導軌焊牢于墻體預埋件上，并焊成以體，各導軌應在同一垂直平面上。

d. Install the pre assembled curtain panel on the drum. Next, install the guide rails. According to the positions specified in the drawings, weld the two sides and upper guide rails firmly onto the wall embedded parts and weld them into a body. Each guide rail should be in the same vertical plane.

e、后，安裝水幕噴淋系統，并與總控制系統連接。裝好后進行試運行，用電動機對門啟閉數次，調整無卡住、阻滯及異常的狀態即可。

e. Afterwards, install a water curtain sprinkler system and connect it to the main control system. After installation, conduct a trial run and use an electric motor to open and close the door several times, adjusting it to a state without jamming, blockage, or abnormalities.

3、自動門水晶卷簾門安裝方法

3. Installation method for automatic door crystal roller shutter door

將電機固定在主板上，把鏈條固定在輪盤和電機底座齒輪連接，試下手柄是否顛倒，如果顛倒，遙控接收盒側方有黑色按鍵，向另一方撥動助即可。

Fix the motor on the motherboard, connect the chain to the wheel disc and motor base gear, and test whether the handle is reversed. If it is reversed, there is a black button on the side of the remote control receiver box. Move the help to the other side.

用尺子量主板和副板的外邊看下尺寸是否正確，如果正確把軸上在側板上，注意要打成一條水平線;再用10個鉆頭打孔50公分，每一個都要直;然后，用14的鏍母焊在軸上，記住一定要焊牢固;再把簾子的片的與軸上的孔對齊，并用快絲固定就可。

Measure the outer edges of the main board and auxiliary board with a ruler to see if the dimensions are correct. If the shaft is correctly placed on the side board, be sure to make a horizontal line; Drill 50 centimeters with 10 drill bits, each one straight; Then, weld the 14 nuts onto the shaft, remember to weld them firmly; Align the center of the first piece of the curtain with the hole on the shaft and fix it with fast wire.

將卷簾門的簾片穿好，兩側用封頭封好。封完后，用繩翻過軸把簾子打孔用繩拴住，再把簾子升上去，切忌一定要牢固。

Thread the curtains of the rolling shutter door and seal both sides with covers. After sealing, use a rope to turn over the shaft to drill holes in the curtain and tie it with a rope. Then, lift the curtain up, making sure it is secure.

把軌道的一端開成人字口，卷簾門簾子調平即可。

Open one end of the track into a zigzag opening and level the curtain of the rolling shutter door.

以上就是對三種不同類型卷簾門安裝方法的全部介紹，相信通過對小編整理內容的認知，應該知道如何安裝卷簾門了吧。如果自己還是不行的，那建議大家請的師傅來進行安裝吧?？梢噪S時聯系我們http://www.kmmhwl.com！

The above is a complete introduction to the installation methods of three different types of rolling shutter doors. I believe that through understanding the content organized by the editor, you should know how to install rolling shutter doors. If you are still unable, it is recommended that you hire a professional technician to install it. Feel free to contact us at any time http://www.kmmhwl.com ！